Part Number: 417362
Material: Body-Brass (Nozzle)
Weight (lbs): 0,5
Part Description: Discharge nozzles are designed to direct the discharge of INERGEN agent using the stored pressure from the cylinders. Ten sizes of nozzles are available. The system design specifies the orifice size to be used for proper flow rate and distribution pattern. The nozzle selection depends on the hazard and location to be protected. Standard nozzles are constructed of brass.

Part Number: 417723
Material: Body-Brass (Nozzle)
Weight (lbs): 0,3
Part Description: Discharge nozzles are designed to direct the discharge of INERGEN agent using the stored pressure from the cylinders. Ten sizes of nozzles are available. The system design specifies the orifice size to be used for proper flow rate and distribution pattern. The nozzle selection depends on the hazard and location to be protected. Standard nozzles are constructed of brass.

Part Number: 417908
Material: Body-Brass (Nozzle)
Weight (lbs): 0,3
Part Description: Discharge nozzles are designed to direct the discharge of INERGEN agent using the stored pressure from the cylinders. Ten sizes of nozzles are available. The system design specifies the orifice size to be used for proper flow rate and distribution pattern. The nozzle selection depends on the hazard and location to be protected. Standard nozzles are constructed of brass.

Part Number: 440000
Weight (lbs): 317.5
Material: Steel-Red Epoxy CR Paint (Cylinder), Brass (Valve), Brass (Safety Relief Valve), Steel-Red Epoxy CR Paint (Shipping Cap)
Part Description: Marinette Filled Cylinder, INERGEN, Std., 575 cu.ft. with CV-98 Valve, 200 Bar ISO/USA/TC. The cylinders are equipped with a 1-inch valve and pressure gauge. Inergen is the most widely know clean suppression Agent for good reasons. It comprises of Naturally occurring inert gases and is extremely effective at suppressing fire where the flamable material doesn’t contain its own oxygen source.

Part Number: 432954
Weight (lbs): 347
Material: Steel-Red Epoxy CR Paint (Cylinder), Brass (Valve), Brass (Safety Relief Valve), Steel-Red Epoxy CR Paint (Shipping Cap)
Part Description: Cylinder, INERGEN, CR, 575 cu.ft. with CV-98 Valve, 200 Bar DOT/TC. The cylinder is factory filled with INERGEN agent. A single cylinder may be used or multiple cylinders can be manifolded together to obtain the required quantity of agent for total flooding. The cylinder valve can be actuated electrically, pneumatically, and/or manually with approved valve actuation components. All valves are equipped with an anti-recoil feature. The cylinders are shipped with a maintenance record card and protective shipping cap attached to the threaded neck of each cylinder. This cap entirely encloses and protects the valve while in shipment.

Part Number: 427888
Material: Forged Steel (Flange), Stainless Steel (Flange Gasket), Stainless Steel (Orifice Plate), Plated Steel-Grade 7B (Bolts)
Weight (lbs): 92
Part Description: The flanged pressure reducer assembly is required to restrict the flow of INERGEN® agent thus reducing the agent pressure down stream of the pressure reducer. The flanged pressure reducer assembly contains a stainless steel orifice plate which is drilled to the specific size hole required based on the flow calculation. The orifice plate provides readily visible orifice identification. The flanged pressure reducer assembly is available in three sizes; 2 1/2, 3, and 4 in. Each size is available in threaded, slip-on, and weld neck flange. All orifice plates must be installed in the piping system with the orifice identification information on the tab facing the pressure inlet side of the system.

Part Number: 427887
Material: Forged Steel (Flange), Stainless Steel (Flange Gasket), Stainless Steel (Orifice Plate), Plated Steel-Grade 7B (Bolts)
Weight (lbs): 46
Part Description: The flanged pressure reducer assembly is required to restrict the flow of INERGEN® agent thus reducing the agent pressure down stream of the pressure reducer. The flanged pressure reducer assembly contains a stainless steel orifice plate which is drilled to the specific size hole required based on the flow calculation. The orifice plate provides readily visible orifice identification. The flanged pressure reducer assembly is available in three sizes; 2 1/2, 3, and 4 in. Each size is available in threaded, slip-on, and weld neck flange. All orifice plates must be installed in the piping system with the orifice identification information on the tab facing the pressure inlet side of the system.

Part Number: 427886
Material: Forged Steel (Flange), Stainless Steel (Flange Gasket), Stainless Steel (Orifice Plate), Plated Steel-Grade 7B (Bolts)
Weight (lbs): 36
Part Description: The flanged pressure reducer assembly is required to restrict the flow of INERGEN® agent thus reducing the agent pressure down stream of the pressure reducer. The flanged pressure reducer assembly contains a stainless steel orifice plate which is drilled to the specific size hole required based on the flow calculation. The orifice plate provides readily visible orifice identification. The flanged pressure reducer assembly is available in three sizes; 2 1/2, 3, and 4 in. Each size is available in threaded, slip-on, and weld neck flange. All orifice plates must be installed in the piping system with the orifice identification information on the tab facing the pressure inlet side of the system.

Part Number: 427885
Material: Forged Steel (Flange), Stainless Steel (Flange Gasket), Stainless Steel (Orifice Plate), Plated Steel-Grade 7B (Bolts)
Weight (lbs): 78
Part Description: The flanged pressure reducer assembly is required to restrict the flow of INERGEN® agent thus reducing the agent pressure down stream of the pressure reducer. The flanged pressure reducer assembly contains a stainless steel orifice plate which is drilled to the specific size hole required based on the flow calculation. The orifice plate provides readily visible orifice identification. The flanged pressure reducer assembly is available in three sizes; 2 1/2, 3, and 4 in. Each size is available in threaded, slip-on, and weld neck flange. All orifice plates must be installed in the piping system with the orifice identification information on the tab facing the pressure inlet side of the system.

Part Number: 427884
Material: Forged Steel (Flange), Stainless Steel (Flange Gasket), Stainless Steel (Orifice Plate), Plated Steel-Grade 7B (Bolts)
Weight (lbs): 40
Part Description: The flanged pressure reducer assembly is required to restrict the flow of INERGEN® agent thus reducing the agent pressure down stream of the pressure reducer. The flanged pressure reducer assembly contains a stainless steel orifice plate which is drilled to the specific size hole required based on the flow calculation. The orifice plate provides readily visible orifice identification. The flanged pressure reducer assembly is available in three sizes; 2 1/2, 3, and 4 in. Each size is available in threaded, slip-on, and weld neck flange. All orifice plates must be installed in the piping system with the orifice identification information on the tab facing the pressure inlet side of the system.