Part Number: 417365
Material: Body-Brass (Nozzle)
Weight (lbs): 0,6
Part Description: Discharge nozzles are designed to direct the discharge of INERGEN® agent using the stored pressure from the cylinders. Ten sizes of nozzles are available. The system design specifies the orifice size to be used for proper flow rate and distribution pattern. The nozzle selection depends on the hazard and location to be protected. Standard nozzles are constructed of brass.

Part Number: 417364
Material: Body-Brass (Nozzle)
Weight (lbs): 0,5
Part Description: Discharge nozzles are designed to direct the discharge of INERGEN® agent using the stored pressure from the cylinders. Ten sizes of nozzles are available. The system design specifies the orifice size to be used for proper flow rate and distribution pattern. The nozzle selection depends on the hazard and location to be protected. Standard nozzles are constructed of brass.

Part Number: 417363
Material: Body-Brass (Nozzle)
Weight (lbs): 0,5
Part Description: Discharge nozzles are designed to direct the discharge of INERGEN® agent using the stored pressure from the cylinders. Ten sizes of nozzles are available. The system design specifies the orifice size to be used for proper flow rate and distribution pattern. The nozzle selection depends on the hazard and location to be protected. Standard nozzles are constructed of brass.

Part Number: 417362
Material: Body-Brass (Nozzle)
Weight (lbs): 0,5
Part Description: Discharge nozzles are designed to direct the discharge of INERGEN® agent using the stored pressure from the cylinders. Ten sizes of nozzles are available. The system design specifies the orifice size to be used for proper flow rate and distribution pattern. The nozzle selection depends on the hazard and location to be protected. Standard nozzles are constructed of brass.

Part Number: 417723
Material: Body-Brass (Nozzle)
Weight (lbs): 0,3
Part Description: Discharge nozzles are designed to direct the discharge of INERGEN® agent using the stored pressure from the cylinders. Ten sizes of nozzles are available. The system design specifies the orifice size to be used for proper flow rate and distribution pattern. The nozzle selection depends on the hazard and location to be protected. Standard nozzles are constructed of brass.

Part Number: 417908
Material: Body-Brass (Nozzle)
Weight (lbs): 0,3
Part Description: Discharge nozzles are designed to direct the discharge of INERGEN® agent using the stored pressure from the cylinders. Ten sizes of nozzles are available. The system design specifies the orifice size to be used for proper flow rate and distribution pattern. The nozzle selection depends on the hazard and location to be protected. Standard nozzles are constructed of brass.

Part Number:451959
Material:Communications gateway, GPIO card (to connect gateway to fire panel)
Weight (lbs): 0,1
Part Description:

Part Number: 426849
Material: Forged Steel (Flange), Stainless Steel (Flange Gasket), Stainless Steel (Orifice Plate), Plated Steel-Grade 5 (Bolts)
Weight (lbs): 78
Part Description: The flanged pressure reducer assembly is required to restrict the flow of INERGEN® agent thus reducing the agent pressure down stream of the pressure reducer. The flanged pressure reducer assembly contains a stainless steel orifice plate which is drilled to the specific size hole required based on the flow calculation. The orifice plate provides readily visible orifice identification. The size of flanged pressure reducer assembly is 4 in. Each size is available in threaded, slip-on, and weld neck flange. All orifice plates must be installed in the piping system with the orifice identification information on the tab facing the pressure inlet side of the system.

Part Number: 426855
Material: Forged Steel (Flange), Stainless Steel (Flange Gasket), Stainless Steel (Orifice Plate), Plated Steel-Grade 5 (Bolts)
Weight (lbs): 92
Part Description: The flanged pressure reducer assembly is required to restrict the flow of INERGEN® agent thus reducing the agent pressure down stream of the pressure reducer. The flanged pressure reducer assembly contains a stainless steel orifice plate which is drilled to the specific size hole required based on the flow calculation. The orifice plate provides readily visible orifice identification. The size of flanged pressure reducer assembly is 4 in. Each size is available in threaded, slip-on, and weld neck flange. All orifice plates must be installed in the piping system with the orifice identification information on the tab facing the pressure inlet side of the system.

Part Number: 426854
Material: Forged Steel (Flange), Stainless Steel (Flange Gasket), Stainless Steel (Orifice Plate), Plated Steel-Grade 5 (Bolts)
Weight (lbs): 46
Part Description: The flanged pressure reducer assembly is required to restrict the flow of INERGEN® agent thus reducing the agent pressure down stream of the pressure reducer. The flanged pressure reducer assembly contains a stainless steel orifice plate which is drilled to the specific size hole required based on the flow calculation. The orifice plate provides readily visible orifice identification. The size of flanged pressure reducer assembly is 3 in. Each size is available in threaded, slip-on, and weld neck flange. All orifice plates must be installed in the piping system with the orifice identification information on the tab facing the pressure inlet side of the system.